NBN30-U4K-N0 123G1xxD
Артикул: 213834
Inductive sensor
5 746 Р
Производитель:
PEPPERL+FUCHS
Поделиться:
Производитель: PEPPERL+FUCHS
Краткое описание: технические характеристики NBN30-U4K-N0 123G1xxD
| General specifications | ||
|---|---|---|
| Switching function | Normally closed (NC) | |
| Output type | NAMUR | |
| Rated operating distance | 30 mm | |
| Installation | non-flush | |
| Assured operating distance | 0 ... 24.3 mm | |
| Actual operating distance | 27 ... 33 mm typ. 30 mm | |
| Reduction factor rAl | 0.31 | |
| Reduction factor rCu | 0.3 | |
| Reduction factor r304 | 0.74 | |
| Output type | 2-wire | |
| Nominal ratings | ||
| Nominal voltage | 8 V | |
| Switching frequency | 0 ... 150 Hz | |
| Hysteresis | typ. 5 % | |
| Reverse polarity protection | yes | |
| Short-circuit protection | yes | |
| Current consumption | ||
| Measuring plate not detected | min. 2.2 mA | |
| Measuring plate detected | ≤ 1 mA | |
| Switching state indicator | LED, yellow | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| NAMUR | EN 60947-5-6:2000 IEC 60947-5-6:1999 |
|
| Electromagnetic compatibility | NE 21:2007 | |
| Standards | EN 60947-5-2:2007 EN 60947-5-2/A1:2012 IEC 60947-5-2:2007 IEC 60947-5-2 AMD 1:2012 |
|
| Approvals and certificates | ||
| UL approval | ||
| Ordinary Location | E87056 | |
| Hazardous Location | E501628 | |
| Control drawing | 116-0451 | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 100 °C (-13 ... 212 °F) | |
| Storage temperature | -40 ... 100 °C (-40 ... 212 °F) | |
| Mechanical specifications | ||
| Connection type | screw terminals | |
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 % |
|
| Core cross-section | up to 2.5 mm2 | |
| Minimum core cross-section | without wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm2 | |
| Maximum core cross-section | without wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm2 | |
| Housing material | PA/metal | |
| Sensing face | PA | |
| Degree of protection | IP68 / IP69K | |
| Mass | 225 g | |
| Note | Tightening torque: 1.8 Nm (housing) | |
| Equipment protection level Ga | ||
| CE marking | [*PD-Z02585A*] | |
| ATEX marking |  II 1G Ex ia IIC T6…T1 Ga The Ex-related marking can also be printed on the enclosed label. |
|
| Standards | EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions |
|
| Appropriate type | NBN30-U.K-N0... | |
| Effective internal capacitance | max. 105 nF ; a cable length of 10 m is considered. | |
| Effective internal inductance | max. 300 µH ; a cable length of 10 m is considered. | |
| Ambient temperature | Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate. Note: Use the temperature table for category 1 !!! The 20 % reduction in accordance with EN 1127-1 has already been applied to the temperature table for category 1. | |
| Equipment protection level Gb | ||
| CE marking | [*PD-Z02585A*] | |
| ATEX marking | II 1G Ex ia IIC T6…T1 Ga The Ex-related marking can also be printed on the enclosed label. |
|
| Standards | EN 60079-0:2012+A11:2013, EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions |
|
| Appropriate type | NBN30-U.K-N0... | |
| Effective internal capacitance | max. 105 nF ; a cable length of 10 m is considered. | |
| Effective internal inductance | max. 300 µH ; a cable length of 10 m is considered. | |
| Maximum permissible ambient temperature | Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate. | |
| Equipment protection level Gc (ic) | ||
| Certificate | PF 13 CERT 2895 X | |
| CE marking | [*PD-Z02586A*] | |
| ATEX marking | II 3G Ex ic IIC T6…T1 Gc The Ex-related marking can also be printed on the enclosed label. |
|
| Standards | EN 60079-0:2012, EN 60079-11:2012 Ignition protection category "ic" Use is restricted to the following stated conditions |
|
| Effective internal capacitance | max. 105 nF ; a cable length of 10 m is considered. | |
| Effective internal inductance | max. 300 µH ; A cable length of 10 m is considered. |
|
| Special conditions | ||
| for Pi=34 mW, Ii=25 mA, T6 | 73 °C (163.4 °F) | |
| for Pi=34 mW, Ii=25 mA, T5 | 88 °C (190.4 °F) | |
| for Pi=34 mW, Ii=25 mA, T4-T1 | 100 °C (212 °F) | |
| for Pi=64 mW, Ii=25 mA, T6 | 66 °C (150.8 °F) | |
| for Pi=64 mW, Ii=25 mA, T5 | 81 °C (177.8 °F) | |
| for Pi=64 mW, Ii=25 mA, T4-T1 | 100 °C (212 °F) | |
| for Pi=169 mW, Ii=52 mA, T6 | 45 °C (113 °F) | |
| for Pi=169 mW, Ii=52 mA, T5 | 60 °C (140 °F) | |
| for Pi=169 mW, Ii=52 mA, T4-T1 | 89 °C (192.2 °F) | |
| for Pi=242 mW, Ii=76 mA, T6 | 30 °C (86 °F) | |
| for Pi=242 mW, Ii=76 mA, T5 | 45 °C (113 °F) | |
| for Pi=242 mW, Ii=76 mA, T4-T1 | 74 °C (165.2 °F) | |
| Equipment protection level Da | ||
| ATEX marking | II 1D Ex ia IIIC T135°C Da The Ex-related marking can also be printed on the enclosed label. |
|
| Standards | EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions |
|
| Appropriate type | NBN30-U.K-N0... | |
| Effective internal capacitance | max. 105 nF ; a cable length of 10 m is considered. | |
| Effective internal inductance | max. 300 µH ; a cable length of 10 m is considered. | |
| General information | ||
| Use in the hazardous area | see instruction manuals | |
| Category | 1G; 2G; 3G | |
Оформить заказ на NBN30-U4K-N0 123G1xxD вы можете в компании compeq-pepperl отправив заявку по почте, а также по телефону или в офисе компании.
Вам может понравиться
