NJ1,5-8-N-Y18812 x23G1xxD

Артикул: 106373

Inductive sensor

13 220 Р

Заказать

Производитель:

PEPPERL+FUCHS

Получить консультацию

Производитель: PEPPERL+FUCHS

Технические данные PDF

Краткое описание: технические характеристики NJ1,5-8-N-Y18812 x23G1xxD

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		1.5 mm
Installation		flush
Assured operating distance		0 ... 0.97 mm
Reduction factor r_Al		0.4
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.85
Output type		2-wire
Nominal ratings
Nominal voltage		8 V
Switching frequency		0 ... 2000 Hz
Hysteresis		0.1 mm
Current consumption
	Measuring plate not detected	min. 2.5 mA
	Measuring plate detected	≤ 1.2 mA
Functional safety related parameters
MTTF_d		11467 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	Standards	EN 60947-5-2:2007 EN 60947-5-2/A1:2012 IEC 60947-5-2:2007 IEC 60947-5-2 AMD 1:2012
Approvals and certificates
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Mechanical specifications
Connection type		cable PUR , 6 m
Core cross-section		0.14 mm²
Housing material		brass
Sensing face		PBT
Degree of protection		IP67
Cable
	Bending radius	> 10 x cable diameter
Equipment protection level Gb
CE marking		[PD-Z02585A]
ATEX marking		II 2G Ex ia IIC T6…T1 Gb The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions
Appropriate type		NJ1,5-8-N..
Effective internal capacitance		max. 20 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 50 µH ; a cable length of 10 m is considered.
Maximum permissible ambient temperature		Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate.
Equipment protection level Gc (ic)
Certificate		PF 13 CERT 2895 X
CE marking		[PD-Z02586A]
ATEX marking		II 3G Ex ic IIC T6…T1 Gc The Ex-significant identification is on the enclosed adhesive label
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection category "ic" Use is restricted to the following stated conditions
Effective internal capacitance		max. 20 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 50 µH ; A cable length of 10 m is considered.
Special conditions
	for Pi=34 mW, Ii=25 mA, T6	70 °C (158 °F)
	for Pi=34 mW, Ii=25 mA, T5	85 °C (185 °F)
	for Pi=34 mW, Ii=25 mA, T4-T1	100 °C (212 °F)
	for Pi=64 mW, Ii=25 mA, T6	68 °C (154.4 °F)
	for Pi=64 mW, Ii=25 mA, T5	83 °C (181.4 °F)
	for Pi=64 mW, Ii=25 mA, T4-T1	100 °C (212 °F)
	for Pi=169 mW, Ii=52 mA, T6	49 °C (120.2 °F)
	for Pi=169 mW, Ii=52 mA, T5	64 °C (147.2 °F)
	for Pi=169 mW, Ii=52 mA, T4-T1	67 °C (152.6 °F)
	for Pi=242 mW, Ii=76 mA, T6	36 °C (96.8 °F)
	for Pi=242 mW, Ii=76 mA, T5	42 °C (107.6 °F)
	for Pi=242 mW, Ii=76 mA, T4-T1	42 °C (107.6 °F)
Equipment protection level Gc (nL)
Standard conformity		EN 60079-15:2003 Ignition protection category "n" Use is restricted to the following stated conditions
Effective internal capacitance C_i		max. 20 nF ; a cable length of 10 m is considered.
Effective internal inductance L_i		max. 50 µH ; A cable length of 10 m is considered.
General		The apparatus has to be operated according to the appropriate data in the data sheet and in this instruction manual. The data stated in the data sheet are restricted by this operating instruction! The special conditions must be observed! The ATEX Directive applies only to the use of apparatus under atmospheric conditions. If you use the device outside atmospheric conditions, consider that the permissible safety parameters should be reduced.
Special conditions
	for Pi=34 mW, Ii=25 mA, T6	70 °C (158 °F)
	for Pi=34 mW, Ii=25 mA, T5	85 °C (185 °F)
	for Pi=34 mW, Ii=25 mA, T4-T1	100 °C (212 °F)
	for Pi=64 mW, Ii=25 mA, T6	68 °C (154.4 °F)
	for Pi=64 mW, Ii=25 mA, T5	83 °C (181.4 °F)
	for Pi=64 mW, Ii=25 mA, T4-T1	100 °C (212 °F)
	for Pi=169 mW, Ii=52 mA, T6	49 °C (120.2 °F)
	for Pi=169 mW, Ii=52 mA, T5	64 °C (147.2 °F)
	for Pi=169 mW, Ii=52 mA, T4-T1	67 °C (152.6 °F)
	for Pi=242 mW, Ii=76 mA, T6	36 °C (96.8 °F)
	for Pi=242 mW, Ii=76 mA, T5	42 °C (107.6 °F)
	for Pi=242 mW, Ii=76 mA, T4-T1	42 °C (107.6 °F)
Equipment protection level Da
CE marking		[PD-Z02585A]
ATEX marking		II 1D Ex ia IIIC T135°C Da The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions
Appropriate type		NJ1,5-8-N..
Effective internal capacitance		max. 20 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 50 µH ; a cable length of 10 m is considered.
Maximum permissible ambient temperature		Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the surface temperature, and the effective internal reactance values can be found on the EC-type-examination certificate. The maximum permissible ambient temperature of the data sheet must be noted, in addition, the lower of the two values must be maintained.
General information
Use in the hazardous area		see instruction manuals
	Category	2G; 3G; 1D