NCB10-30GM40-N0-5M-OG

Артикул: 243379

Inductive sensor

6 942 Р

Заказать

Производитель:

PEPPERL+FUCHS

Получить консультацию

Производитель: PEPPERL+FUCHS

Технические данные PDF

Краткое описание: технические характеристики NCB10-30GM40-N0-5M-OG

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		10 mm
Installation		flush
Assured operating distance		0 ... 8.1 mm
Actual operating distance		9 ... 11 mm typ.
Reduction factor r_Al		0.32
Reduction factor r_Cu		0.32
Reduction factor r₃₀₄		0.72
Output type		3-wire
Nominal ratings
Nominal voltage		8 V
Switching frequency		0 ... 650 Hz
Hysteresis		1 ... 10 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Suitable for 2:1 technology		yes , Reverse polarity protection diode not required
Current consumption
	Measuring plate not detected	min. 3 mA
	Measuring plate detected	≤ 1 mA
Switching state indicator		LED, yellow
Functional safety related parameters
MTTF_d		1870 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Standards	EN 60947-5-2:2007 EN 60947-5-2/A1:2012 IEC 60947-5-2:2007 IEC 60947-5-2 AMD 1:2012
Approvals and certificates
UL approval
	Ordinary Location	E87056
	Hazardous Location	E501628
	Control drawing	116-0452
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated ≤36 V
Ambient conditions
Ambient temperature		-25 ... 80 °C (-13 ... 176 °F)
Storage temperature		-40 ... 80 °C (-40 ... 176 °F)
Mechanical specifications
Connection type		cable PUR (halogen-free) , 5 m , screened , Oil resistant , Flame-retardant as per IEC 60332-1
Core cross-section		2x 0.5 mm²
Housing material		Stainless steel 1.4305 / AISI 303
Sensing face		PBT
Degree of protection		IP66 / IP67
Cable
	Bending radius	> 7.5 x cable diameter
Note		The shield is not connected to the sensor.
Equipment protection level Ga
CE marking		[PD-Z02585A]
ATEX marking		II 1G Ex ia IIC T6…T1 Ga The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions
Appropriate type		NCB10-30GM...-N0...
Effective internal capacitance		max. 105 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 100 µH ; a cable length of 10 m is considered.
Ambient temperature		Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate. Note: Use the temperature table for category 1 !!! The 20 % reduction in accordance with EN 1127-1 has already been applied to the temperature table for category 1.
Equipment protection level Gb
CE marking		[PD-Z02585A]
ATEX marking		II 1G Ex ia IIC T6…T1 Ga The Ex-significant identification is on the enclosed adhesive label
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions
Appropriate type		NCB10-30GM...-N0...
Effective internal capacitance		max. 105 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 100 µH ; a cable length of 10 m is considered.
Maximum permissible ambient temperature		Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate.
Equipment protection level Gc (ic)
Certificate		PF 13 CERT 2895 X
CE marking		[PD-Z02586A]
ATEX marking		II 3G Ex ic IIC T6…T1 Gc The Ex-significant identification is on the enclosed adhesive label
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection category "ic" Use is restricted to the following stated conditions
Effective internal capacitance		max. 105 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 100 µH ; A cable length of 10 m is considered.
Special conditions
	for Pi=34 mW, Ii=25 mA, T6	55 °C (131 °F)
	for Pi=34 mW, Ii=25 mA, T5	55 °C (131 °F)
	for Pi=34 mW, Ii=25 mA, T4-T1	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T6	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T5	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T4-T1	55 °C (131 °F)
	for Pi=169 mW, Ii=52 mA, T6	52 °C (125.6 °F)
	for Pi=169 mW, Ii=52 mA, T5	52 °C (125.6 °F)
	for Pi=169 mW, Ii=52 mA, T4-T1	52 °C (125.6 °F)
	for Pi=242 mW, Ii=76 mA, T6	44 °C (111.2 °F)
	for Pi=242 mW, Ii=76 mA, T5	44 °C (111.2 °F)
	for Pi=242 mW, Ii=76 mA, T4-T1	44 °C (111.2 °F)
Equipment protection level Da
CE marking		[PD-Z02585A]
ATEX marking		II 1D Ex ia IIIC T135°C Da The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions
Appropriate type		NCB10-30GM...-N0...
Effective internal capacitance		max. 105 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 100 µH ; a cable length of 10 m is considered.
Maximum permissible ambient temperature		Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the surface temperature, and the effective internal reactance values can be found on the EC-type-examination certificate. The maximum permissible ambient temperature of the data sheet must be noted, in addition, the lower of the two values must be maintained.
General information
Use in the hazardous area		see instruction manuals
	Category	1G; 2G; 3G; 1D