NCB10-30GK40-N0 x23G1x3D

Артикул: 181124

Inductive sensor

4 982 Р

Заказать

Производитель:

PEPPERL+FUCHS

Получить консультацию

Производитель: PEPPERL+FUCHS

Технические данные PDF

Краткое описание: технические характеристики NCB10-30GK40-N0 x23G1x3D

General specifications
Switching function		Normally closed (NC)
Output type		NAMUR
Rated operating distance		10 mm
Installation		flush
Assured operating distance		0 ... 8.1 mm
Actual operating distance		9 ... 11 mm typ.
Reduction factor r_Al		0.35
Reduction factor r_Cu		0.3
Reduction factor r₃₀₄		0.75
Output type		2-wire
Nominal ratings
Nominal voltage		8 V DC
Switching frequency		0 ... 200 Hz
Hysteresis		1 ... 15 typ. 5 %
Reverse polarity protection		reverse polarity protected
Short-circuit protection		yes
Current consumption
	Measuring plate not detected	min. 2.2 mA
	Measuring plate detected	≤ 1 mA
Switching state indicator		all direction LED, yellow
Compliance with standards and directives
Standard conformity
	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
	Electromagnetic compatibility	NE 21:2007
	Standards	EN 60947-5-2:2007 IEC 60947-5-2:2007
Approvals and certificates
FM approval
	Control drawing	116-0165
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated ≤36 V
Ambient conditions
Ambient temperature		-25 ... 100 °C (-13 ... 212 °F)
Storage temperature		-40 ... 100 °C (-40 ... 212 °F)
Mechanical specifications
Connection type		cable PVC , 2 m
Core cross-section		0.75 mm²
Housing material		PBT
Sensing face		PBT
Degree of protection		IP67
Cable
	Bending radius	> 10 x cable diameter
Equipment protection level Gb
CE marking		[PD-Z02585A]
ATEX marking		II 2G Ex ia IIC T6…T1 Gb The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions
Appropriate type		NCB10-30GK...-N0...
Effective internal capacitance		max. 105 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 100 µH ; a cable length of 10 m is considered.
Maximum permissible ambient temperature		Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate.
Equipment protection level Gc (ic)
Certificate		PF 13 CERT 2895 X
CE marking		[PD-Z02586A]
ATEX marking		II 3G Ex ic IIC T6…T1 Gc The Ex-significant identification is on the enclosed adhesive label
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection category "ic" Use is restricted to the following stated conditions
Effective internal capacitance		max. 105 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 100 µH ; A cable length of 10 m is considered.
Special conditions
	for Pi=34 mW, Ii=25 mA, T6	55 °C (131 °F)
	for Pi=34 mW, Ii=25 mA, T5	55 °C (131 °F)
	for Pi=34 mW, Ii=25 mA, T4-T1	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T6	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T5	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T4-T1	55 °C (131 °F)
	for Pi=169 mW, Ii=52 mA, T6	41 °C (105.8 °F)
	for Pi=169 mW, Ii=52 mA, T5	41 °C (105.8 °F)
	for Pi=169 mW, Ii=52 mA, T4-T1	41 °C (105.8 °F)
	for Pi=242 mW, Ii=76 mA, T6	29 °C (84.2 °F)
	for Pi=242 mW, Ii=76 mA, T5	29 °C (84.2 °F)
	for Pi=242 mW, Ii=76 mA, T4-T1	29 °C (84.2 °F)
Equipment protection level Gc (nL)
Standard conformity		EN 60079-15:2005 Ignition protection category "n" Use is restricted to the following stated conditions
Effective internal capacitance C_i		max. 105 nF ; a cable length of 10 m is considered.
Effective internal inductance L_i		max. 100 µH ; A cable length of 10 m is considered.
General		The apparatus has to be operated according to the appropriate data in the data sheet and in this instruction manual. The data stated in the data sheet are restricted by this operating instruction! The special conditions must be observed! The ATEX Directive applies only to the use of apparatus under atmospheric conditions. If you use the device outside atmospheric conditions, consider that the permissible safety parameters should be reduced.
Special conditions
	for Pi=34 mW, Ii=25 mA, T6	55 °C (131 °F)
	for Pi=34 mW, Ii=25 mA, T5	55 °C (131 °F)
	for Pi=34 mW, Ii=25 mA, T4-T1	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T6	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T5	55 °C (131 °F)
	for Pi=64 mW, Ii=25 mA, T4-T1	55 °C (131 °F)
	for Pi=169 mW, Ii=52 mA, T6	42 °C (107.6 °F)
	for Pi=169 mW, Ii=52 mA, T5	42 °C (107.6 °F)
	for Pi=169 mW, Ii=52 mA, T4-T1	42 °C (107.6 °F)
	for Pi=242 mW, Ii=76 mA, T6	29 °C (84.2 °F)
	for Pi=242 mW, Ii=76 mA, T5	29 °C (84.2 °F)
	for Pi=242 mW, Ii=76 mA, T4-T1	29 °C (84.2 °F)
Equipment protection level Da
CE marking		[PD-Z02585A]
ATEX marking		II 1D Ex ia IIIC T135°C Da The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety" Use is restricted to the following stated conditions
Appropriate type		NCB10-30GK...-N0...
Effective internal capacitance		max. 105 nF ; a cable length of 10 m is considered.
Effective internal inductance		max. 100 µH ; a cable length of 10 m is considered.
Maximum permissible ambient temperature		Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the surface temperature, and the effective internal reactance values can be found on the EC-type-examination certificate. The maximum permissible ambient temperature of the data sheet must be noted, in addition, the lower of the two values must be maintained.
Equipment protection level Dc (tc)
CE marking		[PD-Z02586A]
ATEX marking		II 3D Ex tc IIIC T80°C Dc The Ex-related marking can also be printed on the enclosed label.
Standards		EN 60079-0:2012+A11:2013, EN 60079-31:2014 Protection by enclosure "tc" Some of the information in this instruction manual is more specific than the information provided in the datasheet.
General		The corresponding datasheets, declarations of conformity, EC-type examination certificates, certifications, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents can be found at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet.
Special conditions
	Maximum permissible ambient temperature T_Umax	Values can be obtained from the following list, depending on the max. operating voltage Ub max and the minimum series resistance Rv.
	at U_Bmax=9 V, R_V=562 Ω	63 °C (145.4 °F)
	using an amplifier in accordance with EN 60947-5-6	63 °C (145.4 °F)
Equipment protection level Dc (tD)
General		The apparatus has to be operated according to the appropriate data in the data sheet and in this instruction manual. The maximum surface temperature has been determined in accordance with method A without a dust layer on the equipment. The data stated in the data sheet are restricted by this operating instruction! The special conditions must be adhered to!
Special conditions
	Minimum series resistance R_V	A minimum series resistance RV is to be provided between the power supply voltage and the proximity switch in accordance with the following list. This can also be assured by using a switch amplifier.
	Maximum permissible ambient temperature T_Umax	Values can be obtained from the following list, depending on the max. operating voltage Ub max and the minimum series resistance Rv.
	at U_Bmax=9 V, R_V=562 Ω	63 °C (145.4 °F)
	using an amplifier in accordance with EN 60947-5-6	63 °C (145.4 °F)
General information
Use in the hazardous area		see instruction manuals
	Category	2G; 3G; 1D; 3D